- 您现在的位置：买卖IC网 > Sheet目录322 > DS28EC20+T (Maxim Integrated Products)IC EEPROM 20KBIT TO92-3
DS28EC20: 20Kb 1-Wire EEPROM
MEMORY FUNCTION COMMANDS
The Memory Function Flowchart (Figure 7) describes the protocols necessary for accessing the memory of the
DS28EC20. The target address registers TA1 and TA2 are used for both read and write. To prevent accidental
changes to the data memory or control registers the device employs a BS-flag indicating a “bad sequence”. The
communication between master and DS28EC20 takes place either at standard speed (default, OD = 0) or at
overdrive speed (OD = 1). If not explicitly set into the Overdrive mode, the DS28EC20 assumes standard speed.
For operation at overdrive speed, the DS28EC20 requires V PUP to be 5V ±5%.
WRITE SCRATCHPAD COMMAND [0Fh]
The Write Scratchpad command applies to the data memory and the writable addresses in the register page. After
issuing the Write Scratchpad command, the master must first provide the 2-byte target address, followed by the
data to be written to the scratchpad. The data is written to the scratchpad starting at the byte offset of T[4:0]. The
E/S bits E[4:0] are loaded with the starting byte offset, and increment with each subsequent byte. Effectively, E[4:0]
is the byte offset of the last full byte written to the scratchpad. Only full bytes are accepted. If the last byte is
incomplete its content is ignored and the partial byte flag PF is set. The PF flag is also set if the master ends the
command before a complete target address is transmitted. The PF and BS flags are both cleared when a complete
target address is received.
When executing the Write Scratchpad command, the CRC generator inside the DS28EC20 (Figure 13) calculates a
16-bit CRC of the entire data stream, starting at the command code and ending at the last data byte as sent by the
16 15 2
generator and then shifting in the command code (0Fh) of the Write Scratchpad command, the target addresses
TA1 and TA2 as supplied by the master, and all the data bytes. The master can end the Write Scratchpad
command at any time. However, if the end of the scratchpad is reached (E[4:0] = 11111b), the master can send 16
read-time slots to receive the CRC generated by the DS28EC20.
If a Write Scratchpad is attempted to a write-protected location, the scratchpad is loaded with the data already in
memory, rather than the data transmitted. Similarly, if the target address page is in EPROM mode, the scratchpad
is loaded with the bitwise logical AND of the transmitted data and the data already in memory.
The DS28EC20’s memory address range is 0000h to 0A3Fh. If the bus master sends a target address higher than
this, the DS28EC20’s internal circuitry sets the four most significant address bits to zero as they are shifted into the
internal address register. The Read Scratchpad command reveals the modified target address. The master
identifies such address modifications by comparing the target address read back to the target address transmitted.
If the master does not read the scratchpad, a subsequent Copy Scratchpad command does not work since the
most significant bits of the target address the master sends do not match the value the DS28EC20 expects.
READ SCRATCHPAD COMMAND [AAh]
The Read Scratchpad command allows verifying the target address and the integrity of the scratchpad data. After
issuing the command code, the master begins reading. The first two bytes are the target address. The next byte is
the Ending Offset/Data Status byte (E/S) followed by the scratchpad data beginning at the byte offset (T[4:0]). The
scratchpad data can be different from what the master originally sent. This is of particular importance if the target
address is within the register page or a page in either Write Protection or EPROM modes. See the Write
Scratchpad Command section for details. The master should read through the end of the scratchpad, after which it
receives an inverted CRC16, based on data as it was sent by the DS28EC20. If the master continues reading after
the CRC, all data are logic 1s.
11 of 27
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DS301X
KWIK-CHG DESIGNATION STRIP SGL
DS3030W-100#
IC NVSRAM 256KBIT 100NS 256BGA
DS3045W-100#
IC NVSRAM 1MBIT 100NS 256BGA
DS3050W-100#
IC NVSRAM 4MBIT 100NS 256BGA
DS3065W-100#
IC NVSRAM 8MBIT 100NS 256BGA
DS3065WP-100IND+
IC SRAM 3.3V 8MB 34POWERCAP MOD
DS3070W-100#
IC NVSRAM 16MBIT 100NS 256BGA
DS321X
KIT X-WIDE DESIGN STRIP VERT
相关代理商/技术参数
DS28EC20-224-BB+
制造商:Maxim Integrated Products 功能描述:- Rail/Tube
DS28EC20P
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:DS28EC20_1203
DS28EC20P T
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:DS28EC20_1203
DS28EC20P+
功能描述:电可擦除可编程只读存储器 20Kb 1-Wire 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
DS28EC20P+T
功能描述:电可擦除可编程只读存储器 20Kb 1-Wire 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
DS28EC20P-224-BB+T
制造商:Maxim Integrated Products 功能描述:- Tape and Reel
DS28EC20Q-A5A-5A+T
制造商:Maxim Integrated Products 功能描述:20KB 1-WIRE EEPROM - Tape and Reel
DS28EC20Q-A5A-5A+W
制造商:Maxim Integrated Products 功能描述:20KB 1-WIRE EEPROM - Rail/Tube